Keeper of the Ark.
The Ark @fosscad.io beginner friendly fully diy build.
Originally posted by u/fullyloadedmagazine at 2025-06-21T17:31:53Z
im sure you get this question a lot but for some reason my reddit search bar wont load anything right now so ill just ask. whats an easy to assemble, easy to print, almost or fully diy semi-auto build that i can make without any real firearm parts? i just joined the beta of "the ryno" and so far its going great but i have an urge to make more. the only problem is that im still very inexperienced so im really looking for something easy.
The Ark @fosscad.io Filament recommended for a nylaug?
Originally posted by u/Agitated-Werewolf846 at 2025-06-21T17:28:09Z
Hello everyone I was wondering if y'all had any recommendations for printing out a nylaug i know it has to be a carbon fiber nylon but I've heard that it has issues with water absorption and expanding even after its been annealed and there are so many options out there that it's kinda overwhelming to pick out what filament i should use for it
The Ark @fosscad.io Daichi upper, Cursed Ranch Rifle lower
Originally posted by u/PancakesandScotch at 2025-06-21T17:15:00Z
Had a mossberg stock in the closet and a printed mlok handguard that started all this but it’s getting there now
Printing a bushing for the barrel to center in the handguard and a plug for the rear of the BCG then it’ll be time to try and fit this double trigger ordeal.
Bailed on using one of my spare Tubee uppers so I could use a charge handle I also had in my parts drawer.
I’ve got some long Glock mag springs that i may use to make some shorter straight mags, just don’t like the longer curved mag look on this one so open to suggestions there
There is truly no point to this build. But I guess that’s the point to this build.
The Ark @fosscad.io Aside from recoil pads what do you use tpu for?
Originally posted by u/Intelligent_Step_855 at 2025-06-21T16:37:04Z
Got a 50 buck Amazon gift card, debating on buying a spool of tpu or cf nylon
The Ark @fosscad.io Bed_liner.exe
Originally posted by u/gunzrcool at 2025-06-21T16:29:11Z
The Ark @fosscad.io Super Safety Q
Originally posted by u/Minimum_Zebra8531 at 2025-06-21T16:13:56Z
Have a good ol PSA-15 with a deez nutz tactical super safety kit installed. Gun runs in semi auto great, however when put into full auto only shoots 2-3 shots and next round is not chambering after that. I just get a dry fire click.
Im running a geissele H3 buffer with 2 quarters behind it. I am not running a suppressor, so I wouldn’t think this would be a gas issue. Maybe take the quarters out?
The Ark @fosscad.io Reliable 1022 mag?
Originally posted by u/Upstairs-Panic-1027 at 2025-06-21T15:35:25Z
The Ark @fosscad.io 20mm Riser plate for RMR red dots
Originally posted by u/Available-Captain776 at 2025-06-21T15:02:51Z
Designed a riser plate for those using RMR red dots, this just lifts it 20mm for a better sight picture. On makerworld as "RMR Red Dot Riser Extension" !
The Ark @fosscad.io Decker9 Testing This Weekend
Originally posted by u/BowTiedAnkylo at 2025-06-21T14:53:36Z
What better way to start the weekend than with some Decker9 testing? The beta is coming along nicely, btw. I think you all are going to be really happy with all the options and features this has. Can't wait to be able to share them with you guys!
The Ark @fosscad.io Failed successfully
Originally posted by u/Unmentioned77 at 2025-06-21T14:32:37Z
So printed this stock last night and had a massive layer shift. Funny enough it didn't fail completely and I got a usable part. I'm looking for some help dialing in my settings on my Ender 3. Most of my printing experience is with a Anet a8. So my main issue is over extrusion on the bottom few layers. I ran 100% infill, and I think the over extrusion compounded and the nozzle caught on the print causing the layer shift. The belts are tight, they almost hum when plucked. Simultaneously I'm getting under extrusion around horizontal holes, I'm guessing thats to do with retraction settings. So printed a benchy just before starting the bigger print. It didn't look the best but good enough for me, so I included those pictures too.
Settings: Filament 1.75 ABS, layer height 0.2mm, print speed 50mm/s, nozzle temp 250, bed temp 100, alm
The Ark @fosscad.io 10/22 mag plunger
Originally posted by u/LongBranch1949 at 2025-06-21T14:28:43Z
I’m building a Decimator from left over 10/22 and AR parts. The only extra part I don’t have laying around is the magazine plunger. Does anyone know if a stl exists? I know a new one is cheap. Just looking to print it if it’s a possibility. TIA.
The Ark @fosscad.io New to the community
Originally posted by u/trot_lover at 2025-06-21T14:11:24Z
Hey guys. Ive been following navi, psr, yz, etc. For a couple of years now and just last month i bought an ender v3. I live in a super restrictive country with gun laws, i was wondering is it possible to use an squirted upper and lower and not fucking die of an explosion?
The Ark @fosscad.io Printed handguards?
Originally posted by u/MOOKAJAMS at 2025-06-21T12:40:13Z
I went searching and realized… there’s not a lot of traditional ar handguards. Designs only focus on Mac, orca, dear22, sg22, mp5 and bidens bane. Any one knows any specific designs that support 556 upper?
The Ark @fosscad.io Layer shift
Originally posted by u/KarmaWasTaken01 at 2025-06-21T12:14:31Z
Left this print on overnight and came back to a nice little beautiful layer shift so I was just honestly wondering if it would still be salvageable with this tiny layer shift because this piece was coming out pretty good if not it’s ok back the reprinting lol
The Ark @fosscad.io No access to defcad.💔
Originally posted by u/Some-Ad-385 at 2025-06-21T08:49:10Z
I've tried and tried and tried, still no access even with setting device location to Texas with residential VPN, anyone wanna help me out by forwarding some files or give some advice around this issue?
The Ark @fosscad.io Lock Pick upgrades.
Originally posted by u/Apprehensive_Tap4837 at 2025-06-21T07:55:54Z
A couple more items for the lock pick.
- Conversion 1913 rail (used when placing a lock pick in a standard 1022 stock)
- Stronger stand alone, nothing wrong with the old one but this one is stronger, more compact, and requires no hardware.
Next Will be a new chassis that's notched in the rear and sets farther back on the stand alone to remove any possibility of flex.
The Ark @fosscad.io Supports keep touching model with no interface
Originally posted by u/Only_Negotiation_437 at 2025-06-21T07:51:24Z
Sovol Sv06
.4mmHardened steel Nozzle
printing pa612 cf
really just a slicer problem....my supports are going through the support interface and touching the model. I have already tried adjusting the z gap of the interface but nothing. I am using orca. Cura never gave me this problem but i like orca cause it made calibrating the filament a breeze and there's more options. these supports are giving me a big problem however. support settings in photos
The Ark @fosscad.io Ok boomer question
Originally posted by u/No-Forever-1950 at 2025-06-21T05:07:55Z
Would the ok boomer 1911 work with a 1911 compact or officer parts like the one pictured above.
The Ark @fosscad.io Found a crack with the widest spot at .117 on both upper receivers of the Hd22c, been printing this upper today and it’s almost finished. I’ll shine a light in it to see if it’s there. This sucks😢
Originally posted by u/-250smacks at 2025-06-21T04:50:45Z
The Ark @fosscad.io M1337 Bearings
Originally posted by u/tophercookie at 2025-06-21T03:23:42Z
Just wanted to remind every one if you are looking to do the M1337 build you can contact Annie at Lily bearings. They will ship directly from China. In the email just put you need the bearings for the M1337 build. She will know exactly what you need. If you need the email please reach out to me. Reddit doesn’t like that stuff posted. Below is what I paid.
KD045CP0 bearing 1pc US$107.57/pc R24-2RS bearing 2pcs US$7.96/pc6810 2rs bearing 1pc US$6.85/pcR16-2RS bearing 2pcs US$5.38/pcR8-ZZ bearing 6pcs US$1.74/pcR188zz bearing 12pcs US$1.15/pc683zz bearing 6pcs US$1.15/pc Total: US$172.24
Once you get it in the mail you will have to pay import fees. That was another $32.
If you have any questions please reach out!
!
u/Open_Source1096 · 2024-06-08 22:23:22 UTC · score 1
Sending you a PM now will find photos